NES / SNES Controller Button Signal Breakout Board
Connect an NES or SNES gamepad controller to this PCB and it will continually read the button states from the gamepad's internal 4021 shift register (clocked by an ATTiny26L on this PCB).
The button states are decoded and sent out to dedicated GPIO pins.
The gamepad can then be used as a controller for other projects.
Example: The NES gamepad "up" direction is pressed, the PCB "Up" pin goes low. The button is released, the "Up" pin goes high.
The ATTiny26L is programmed from the Arduino IDE using the ATTinyCore board file (version 2 or later needed).
NES and SNES 7 pin controller sockets are available on AliExpress to make adapter cables to plug into the PCB.
NES / SNES Controller Button Signal Breakout Board
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(0)
- Likes(1)
- Francisco Meza Dec 26,2023
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by Gadget Reboot
- Op Amp Buffer with In/Out Guitar Jacks The pcb has a guitar input and output jack to easily connect to a breadboard for guitar effect circu...
- 16 Channel Audio Loop Switcher This is a 16 channel audio loop switcher with 16 inputs and 16 outputs.Analog signals within a +/- 5...
- 16 Switches to RS485 Output Commands Up to 16 switches or 5v/gnd logic inputs can be monitored and when asserted (input = gnd), a sketch ...
- MCP42100 Digital Pot Breakout PCB This breakout board for the MCP42100 dual digital pot has headers that are spaced for breadboard com...
- Power Supply DC Jack/Screw Term/0.1" Header Breakout with PTC This breakout board allows connecting a power source via 2.1x5.5mm DC jack, 7.62mm screw terminals, ...
- 16x16 Analog Switch This 16x16 analog crosspoint switch uses two MT8816 8x16 switch ICs cascaded for a larger matrix.The...
- Line Level Stereo Input to 3 Stereo Output Sharing PCB This audio sharing board will take a stereo line input from a 3.5mm jack, buffer it and send it out ...
- MIDI Breakout In/Out/Thru This MIDI breakout board has 5 pin DIN jacks and Type A configured 3.5mm TRS jacks for Midi In, Midi...
- Tandy CoCo Joystick Adapter - Use Digital Inputs for Analog X,Y axis Use 5v/GND digital signals to control the analog joystick input of a Tandy Color Computer.When input...
- Guitar Stomp Switch and LED Breakout Board This PCB takes a 9 pin 3PDT guitar effect on/off stomp switch along with an LED and resistor, and pr...
- HV5222 Breakout Board HV5222 32 bit high voltage shift register breakout boardThe driver chip has open drain outputs that ...
- DTMF Decoder 3.3v MT88L70 This DTMF decoder uses the MT88L70, powered by 3.3v and interfacing with 3.3v GPIO to decode the tou...
- PT2399 Echo IC Breakout Board The PT2399 is a low-fi echo IC with built in ADC, Ram, and DAC.It uses a handful of external resisto...
- CD4040 Binary Counter Breakout PCB Dual 4040 12 bit ripple carry binary counters.Two surface mount counters on a breakout board that fi...
- 555 Adjustable Duty Cycle and Frequency Easy to use 555 oscillator with potentiometers to adjust duty cycle and frequency.The 5 pin header c...
- DMX RS485 to TTL Isolated Adapter with 3 pin XLR This pcb can be assembled as either a DMX transmitter or receiver interface (the BOM is set up to bu...
- Phone Line Simulator (POTS Land Line) Plug an old land line phone or other device into the RJ11 jack, pick up the phone and hear a dial to...
- 1/4" Phone Jack TRS Breakout PCB This PCB accepts 4 stereo 1/4 inch phone jacks and provides TRS connections on 2.5mm headers, which ...
-
IoT Indoor system with ESP32 to monitor Temperature, Humidity, Pressure, and Air Quality
270 0 1 -
Naruto Multi-color PCB printed with UV technology
112 2 1 -
-
-
-
-