|
EagleAutodesk
|
Dual Korg MS20 VCF for Eurorack
Build your own Dual MS20 VCF....this is Euro format, 15HP, +/-12V.
This project requires 2 of the PCBS you can find on the PCBWAY community site: "MS 20 clone voltage controlled filter". Each board is a single MS20 filter based on the schematic here.
This project has the other 2 PCB's you need to build this dual filter: one is the PCB for the pots and jacks, another from the front panel.
For the front panel, consider using black with white silks, and note in the order you want the product number on the back side of the board.
Again: to build the entire project you need 4 PCB's.
This project is detailed in the "audioDIWHY" series of blog posts--find out more about the project in the blog post here and here and more about the MS20 VCF boards here.
Building it: Almost all the board is through-hole parts; there is one SOIC op amp used for the on board mixer; not too difficult to solder with a fine tipped iron and some fine gauge solder.
Have fun building!
Dual Korg MS20 VCF for Eurorack
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(0)
- Likes(1)
- Engineer Feb 17,2024
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by AudioDIWHY
- Vactrol Based Audio Envelope Follower An audio envelope follower based on a 5C3 Vactrol.Eurorack format--6HP. Uses +/- 12V at about 20mA p...
- Warm Floater Eurorack Power Extender I ran out of physical connections on my Eurorack Power supply. This PCB supplies 1 input and 3 outpu...
- "KiCADSR" Euro Envelope Generator This is my first project using KiCAD for EDA instead of Autodesk Eagle. I wanted to see if I had the...
- Low Noise Preamp based on Arp 2600 Synthesizer The Arp 2600 synthesizer has a preamp that takes an unbalanced signal and amplifies it 10x, 100x, an...
- Arp 2600 clone--inverter-mixer The ARP2600 is a legendary, classic semi-modular analog synthesizer. Its voltage processor circuitr...
- SEEED XAIO RP2040 ADC and Buffer Board The SEEED XAIO RP2040 is a fantastic little dev board, featuring the RP2040 MCU.I needed a buffered ...
- RP2040 Clock Multiplier Development Board I have some RP2040 code to write and didn't want to Breadboard the hardware, so I whipped up a devel...
- Anything to Clock--LM311 based If you need a precision rectifier to turn audio or LFO signals into clock, this small circuit gets t...
- Anything to Clock--Precision Rectifier For more details please see this blog post:https://audiodiwhy.blogspot.com/2024/04/anything-to-clock...
- Hardware Encoder Debounce Board For details about this project please see this blog post: https://audiodiwhy.blogspot.com/2024/01/ro...
- DSPG1 4 voice synthesizer on a single PCB The DSPG1 is a $20 IC--along with a handful of external parts this chip gives you a complete a 4 voi...
- Son of Warm Floater I ran out of power spigots in my Eurorack, this simple project takes a 16 conductor +/- 12V, GND, 5V...
- ARP 2600 Audio Switch The legendary ARP2600 has a pop free/click free clock driven analog switch. Each rising clock switch...
- DG401 Audio CMOS switch Experimenter's Board I was curious how the DGx0x series analog switches sounded and didn't want to breadboard a DG401 wit...
- ARP2600 Lag Processor Clone The Arp 2600 "Voltage Processor" section is one of the many designs that makes this legendary synth ...
- Eurorack Bench Mixer I needed a bench mixer for my Eurorack workbench setup--to replace the Frac-formatted audio bench ge...
- Dual Korg MS20 VCF for Eurorack Build your own Dual MS20 VCF....this is Euro format, 15HP, +/-12V.This project requires 2 of the PCB...
- MS20 Clone Voltage Controlled Filter The Korg MS20 is a lengendary semi-modular monophonic synthesizer. The PCB here is the MS20's VCF l...
-
(DIY) COMMODORE 64 DEAD-TEST (781220) DIAGNOSTIC CARTRIDGE
51 0 0 -
Creative Micro Designs Inc. CMD FD-2000 / FD-4000 3D Printable Case
207 0 0 -
Creative Micro Designs Inc. CMD FD-2000 / FD-4000 Metal Case
271 0 0 -
-
-
IoT Indoor system with ESP32 to monitor Temperature, Humidity, Pressure, and Air Quality
750 0 3 -
Naruto Multi-color PCB printed with UV technology
267 2 1