How to Balance a Battery Pack With USB or the Traditional Method - TP4056
Hi guys, today let's see together how to balance a battery pack through a very common micro-USB connector or with the traditional method
Step 1: Why Balance Matters
When charging a battery pack it may happen that, once charged, measuring with the multimeter there is a voltage slightly lower than what we expected (such as 41.5 V instead of 42V).
If so, then most likely, inside the battery pack, there is a cell (or several cells in parallel) that has a lower voltage than the others.
This is a problem because most of the BMS (i.e. the card that deals with the management of the battery packs) on the market stop charging the entire battery pack as soon as even a single cell reaches 4.2V and does not take into account the other cells that may still charge.
Conversely, if there is a cell in the battery pack that is at 50%, the BMS will cut off the power supply because it will detect that there is a low cell without knowing that all the others are charged.
Step 2: Detect the Most Discharged Cell
First you have to remove the cover, the box or in any case the casing of the battery pack. Don't worry, if you've never done it, there's nothing to worry about.
You just have to pay attention to where you put your hands because the currents and voltages involved can be very dangerous.
Once you open the battery pack, you need to look for the BMS (Battery Management System) which is probably the only card that will be inside.
Once this is done it will be necessary to remove the 10pin connector called JST which has connected to it all the positives and negatives of each cell in series.
After that, through the use of the multimeter it is necessary to understand to which pair of pins the poles of the cell (which is made up of several cells in parallel) which is more discharged. To do this, you will need to insert the multimeter's leads from pin to pin with a one-pin pitch.
At the same time you will read on the tester the same or similar values ??for each pair of pins and only when you reach the most discharged cell will the multimeter show a lower value.
Step 3: Traditional Method
The first method is the traditional one which is to charge the most discharged cell, balancing the battery pack, with the help of a bench power supply or any type of direct current power supply that can have a voltage value of 4, 2V.
Once you turn on the power supply and after setting it to 4.2V, just disconnect the banana connectors used before by the tester and connect them to the power supply.
I recommend, it is absolutely important that the two connectors are disconnected from the multimeter one at a time because if the two connectors were to touch, a wire of that section would melt in a fraction of a second.
Once this is done, all you have to do is wait for the battery to charge.
This was the most traditional method but also the most inconvenient because it forces you to have a power supply on for several hours which, in addition to being oversized for this job, is also very bulky and, if it has a fan as in my case, noisy.
So now let's see how to do the same job but in much much more efficient way.
Step 4: Best Method: Charge With USB
The second method is to use a micro USB cable to charge the cell.
To do this we will use a micro USB module containing the TP4056 chip which, in addition to serving for this purpose, is also very useful for protecting and using single cells, protecting everything from overcharge, over-discharge, overvoltage, overcurrent and much more.
Our goal, however, is to use it only to load the cells, so we just need to simply solder two cables to pin B + and B- of the module and that's it.
Once this is done, if we try to connect a battery and the USB cable, as you can see from the photos, the charging of the cell starts and we notice it from the red LED that lights up.
Once we have ascertained that everything works correctly, all we have to do is insert the pins of the wires just soldered to the positive and negative of the most discharged cell of the battery pack through the connector in the BMS
Don't worry, if you get the polarity wrong you will notice it immediately from the burn that you will cause by touching the module.
In these cases, having around high voltage and ability to deliver very high current, I prefer to cover the module with a sheath so as not to run the risk of touching something to something else
Step 5: It's Done!
Well, you will now have to wait for the light to turn blue and you are done balancing your cells in order to ensure much greater health for the battery pack. In a future article we will see how to add an automatic cell balancer to make it do this job.
How to Balance a Battery Pack With USB or the Traditional Method - TP4056
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(0)
- Likes(1)
- ubuntupunk Mar 09,2023
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by Maurizio Miscio
- DIY UPS (Emergency Battery) for Routers So It Won't Turn Off When the Breakers Are Off Hi, today we are building a UPS or backup battery for the router / modem so that it does not turn of...
- How to Make a Fiido D4S Battery (kind of) Removable Do you guys have a Fiido D4S but not a place to charge it?You know, your house is too small to park ...
- How to (Re)build an Ebike Charger and Add a Fan to Keep It Cool Hi guys. In the last article we saw how to make a Fiido D4S Battery removable, but now to charge it ...
- Automatically Turn Off the Power Strip of the Computer (monitor, Speakers, Etc.) When You Shut Down the Computer. If you have a desktop computer at home, you will know better than me how boring it is to turn off th...
- How to Disable the Throttle of an Electric Bike With an Invisible Switch Hi folks, in this tutorial we will see how to disable the throttle of an electric bike (in my case a...
- Adding a Female Aux Jack to Your Old Headphone - the Best Upgrade You Can Do! Have you ever broken a headphone jack? Probably the answer is yes! Or simply have you ever had issue...
- Easiest Way to Discharge a Ebike Battery Hi guys, welcome to this new tutorial. Today I will show you the easiest way to discharge a Ebike Ba...
- Arduino School Bell - Simple DIY Hi guys, in this article we are going to see how to make a circuit with Arduino and some other compo...
- Arduino Large and Productive Solar Tracker - Do It Yourself Hi everyone! In this article we are going to see how to build a solar tracker that knows how to do t...
- Arduino Robotic Arm Controlled by Touch Interface Hello. Today I'm here to see with you how I built a robotic arm with Arduino and a graphic touch int...
- DIY Bench Variable Power Supply - ZK-4KX Hello to all boys and girls, today we will see together how I made a very compact DIY benchtop varia...
- How to Balance a Battery Pack With USB or the Traditional Method - TP4056 Hi guys, today let's see together how to balance a battery pack through a very common micro-USB conn...
- Single 18560 Battery Charger With TP4056 Hi guys, in this article we will see how to make a very convenient single charger for 18650 cells so...
- The Best Mini OLED Display I've Ever Tried! - DF Robot 5.5 'HDMI OLED-Display With Touchscreen IntroHi guys, today let's unpack together the best mini display I've ever seen that I was extremely ...
- Let's Add an Active Balancer to the Electric Bike Battery Intro:Hi guys, today we add an active balancer to the battery of our ebike so as not to risk some ce...
-
-
IoT Indoor system with ESP32 to monitor Temperature, Humidity, Pressure, and Air Quality
401 0 2 -
Naruto Multi-color PCB printed with UV technology
152 2 1 -
-
-
-