|
C36191 - Connector 1 |
x 1 | |
|
ANKX01-0093_C129604 - Connector 2 |
x 1 |
Coax SMA Hat for Raspberry Pi - Without Filter
Raspberry pi Coax SMA Pcb - Without Filter
Raspberry Pi 4 Model B : https://amzn.to/3S8a9vY (Amazon)
Expansion board for Raspberry PI allowing to use coaxial SMA output instead of direct wire connection to GPIO to connect radio equipment (antennas, amplifiers, switches, etc.) when working with the rpitx package.
The PCB is installed by attaching to the GPIO of the Raspberry PI and can be additionally fixed by using the holes on the Raspberry PI and expansion board side.
In Datasheets and Schematics directories, you can find all necessary technical documentation for the used components and schematic files in PDF format. If you only need GERBER files, you can find them in the appropriate Gerbers directory. In the EasyEDA directory, you can find a list of files for implementing the ready device (files can be imported into EasyEDA editor). Based on submitted files, you can order PCB from factory manufacturing make the device independently.
basic device characteristics:
PCB versions:
PCB_rpitx-coax-pcb-NOFILTER - no filtering, only output to SMA connector
- RF connector: SMA
- Feed line: 50 Ohm coaxial cable
- Used PCB Material: FR-4
- PCB thickness: 1.6 mm
- PCB copper weight: 1 oz
If you are unfamiliar with it, RPiTX is a program for Raspberry Pi single board computers that allows you to transmit almost any type of signal on frequencies between 5 kHz up to 1500 MHz with nothing more than a wire connected to a GPIO pin. However, it is highly recommended that appropriate filtering be used if you are transmitting with an amplifier or longer range antenna as the RPiTX contains harmonics that can cause interference with other devices.
For More informations : https://github.com/IgrikXD/rpitx-coax-pcb/tree/master
Coax SMA Hat for Raspberry Pi - Without Filter
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(0)
- Likes(1)
- EL M Nabil Jul 25,2023
- 1 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
-
10design
-
10usability
-
10creativity
-
10content
More by EL M Nabil
- Coax SMA Hat for Raspberry Pi - Without Filter Raspberry pi Coax SMA Pcb - Without FilterRaspberry Pi 4 Model B : https://amzn.to/3S8a9vY (Amazon)E...
- Coax SMA Hat for Raspberry Pi - With GP1212-GP731 Filter Raspberry pi Coax SMA Pcb - With GP1212-GP731 FilterRaspberry Pi 4 Model B : https://amzn.to/3S8a9vY...
- CANPico v2 Raspberry Pi Pico : https://amzn.to/41P4ZYQ (Amazon)The Yes We CAN repositoryThis repository contain...
- OBD II GPS Tracker OBD II GPS Tracker OBD ii GPS tracker is the most convenient vehicle GPS tracking device. This track...
- LoRa Pro Mini LoRaProMini - A low power LoRaWAN NodeA LoRaWAN sensor node, based on ATmega328P MCU (Arduino Pro Mi...
- CAN HAT for Raspberry Pi CAN HAT for Raspberry PiRaspberry Pi 4 Model B : https://amzn.to/3S8a9vY (Amazon)Raspberry Pi Zero 2...
- GNSS HAT for Raspberry Pi Raspberry Pi 4 Model B : https://amzn.to/3S8a9vY (Amazon)Introduction to mosaicHATWhat is mosaicHAT?...
- HoneyPi - Connect various sensors To Raspberry Pi HoneyPi-PCB 3.0xRaspberry Pi 4 Model B : https://amzn.to/3S8a9vY (Amazon)Raspberry Pi Zero 2 W : htt...
- GamePort USB adapter - necroware Necroware's GamePort AdapterFor more information: https://github.com/necroware/gameport-adapterFor R...
-
IoT Indoor system with ESP32 to monitor Temperature, Humidity, Pressure, and Air Quality
336 0 2 -
Naruto Multi-color PCB printed with UV technology
134 2 1 -
-
-
-
-